S2KI Honda S2000 Forums
Finished product with heat shrink wrap.
Finished product with heat shrink wrap.
0 2017/01/22 16:03:49
More heat shrink wrap.
More heat shrink wrap.
0 2017/01/22 16:03:50
The power cable feeds through the firewall like so.
The power cable feeds through the firewall like so.
0 2017/01/22 16:03:51
And under the dash as shown, and with loom wrapped around it.
And under the dash as shown, and with loom wrapped around it.
0 2017/01/22 16:03:52
I fed my wire through the plastic guide after popping it open.
I fed my wire through the plastic guide after popping it open.
0 2017/01/22 16:03:53
The cable will go into the trunk through behind the passenger seat as shown.
The cable will go into the trunk through behind the passenger seat as shown.
0 2017/01/22 16:03:54
Then, I crimped on the relay terminal, and popped the wire into the relay connecter as per the instructions.
Then, I crimped on the relay terminal, and popped the wire into the relay connecter as per the instructions.
0 2017/01/22 16:03:57
This is the connector that plugs into the top of the fuel pump carrier. I popped the rear cap off from the three tabs with the depinning tool.
This is the connector that plugs into the top of the fuel pump carrier. I popped the rear cap off from the three tabs with the depinning tool.
0 2017/01/22 16:08:52
The blue face comes off by using the depinning tool to pry it off from the depression on the side of the face next to my thumb there.
The blue face comes off by using the depinning tool to pry it off from the depression on the side of the face next to my thumb there.
0 2017/01/22 16:08:55
Here, you can see the second piece of power wire connected to its respective slot in the relay connector, after the relay terminal was installed. I have the relay shown as it will go into the connector. (I ended up needing to purchase a bosch 30 amp relay after the bueller relay went bad on me.).
Here, you can see the second piece of power wire connected to its respective slot in the relay connector, after the relay terminal was installed. I have the relay shown as it will go into the connector. (I ended up needing to purchase a bosch 30 amp relay after the bueller relay went bad on me.).
0 2017/01/22 16:08:58
The thick grounding wire will have this end crimped on and will be attached to a bolt in the trunk. I used sanding paper to remove the paint from the grounding spot.
The thick grounding wire will have this end crimped on and will be attached to a bolt in the trunk. I used sanding paper to remove the paint from the grounding spot.
0 2017/01/22 16:09:05
The two top slots are empty in this pic, shown after removing the pins.
The two top slots are empty in this pic, shown after removing the pins.
0 2017/01/22 16:09:19
These are the power and ground cable removed from the pump connector. The will serve as a switch signal for the relay.
These are the power and ground cable removed from the pump connector. The will serve as a switch signal for the relay.
0 2017/01/22 16:09:20
These are the two wires after being pulled out from beneath the cover plate.
These are the two wires after being pulled out from beneath the cover plate.
0 2017/01/22 16:09:28
Relay terminals installed.
Relay terminals installed.
0 2017/01/22 16:09:29
These are the new power and ground wires with pins attached, ready for insertion into the plug.
These are the new power and ground wires with pins attached, ready for insertion into the plug.
0 2017/01/22 16:16:44
The wire will go into the connector through the back as shown.
The wire will go into the connector through the back as shown.
0 2017/01/22 16:16:46
Here is the pin.
Here is the pin.
0 2017/01/22 16:16:50
These are the power and ground installed into the rear of the connector. The red shrink wrap was added because I almost cut the wire too short. The coating was not pierced, but I figured it best to wrap it in case it wears down over time.
These are the power and ground installed into the rear of the connector. The red shrink wrap was added because I almost cut the wire too short. The coating was not pierced, but I figured it best to wrap it in case it wears down over time.
0 2017/01/22 16:19:08
Capped down.
Capped down.
0 2017/01/22 16:19:12
Face installed.
Face installed.
0 2017/01/22 16:19:16
Plugged into the top of the pump carrier.
Plugged into the top of the pump carrier.
0 2017/01/22 16:19:17
Capped down. These wires are later covered in loom and then wrapped in electric tape.
Capped down. These wires are later covered in loom and then wrapped in electric tape.
0 2017/01/22 16:19:19
Finished product with the relay in place, and looming completed. I had to replace this relay with a bosch after a few weeks.
Finished product with the relay in place, and looming completed. I had to replace this relay with a bosch after a few weeks.
0 2017/01/22 16:25:44
Shot of the wire going to the plug under the plate.
Shot of the wire going to the plug under the plate.
0 2017/01/22 16:25:49
Ground wire.
Ground wire.
0 2017/01/22 16:25:51
Wiring diagram.
Wiring diagram.
0 2017/01/22 16:25:52
0 2024/05/01 06:37:39
0 2024/05/01 06:39:13