Genuine Honda Parts Thread
#2741
UK Trader
Thread Starter
Thanks for the order
Couple of other things we have added to the site lately:-
JDM/USDM Rear Bumper (unpainted)
S2000 Clutch Release Bearing
Couple of other things we have added to the site lately:-
JDM/USDM Rear Bumper (unpainted)
S2000 Clutch Release Bearing
#2742
UK Trader
Thread Starter
is there any glue or bonding tape for fitting the weather strips?
part number 72381S2A013 WEATHERSTRIP, R. ROOF SIDE DOOR (or Lings image part number PFKL785135)
The roof was jetwashed by a young idiot at the bodyshop, and now that seal drips in the middle joint. The seal seems to have been fitted to the frame by some white glue/tape/boding putty, which is no longer sticky.
I assume this glue helps the weather strip stay stretched, it appears to be about 2mm too short for a proper seal. I can open the window and stretch the seal that little bit, then close the window, and everythings fine, But opening the window/roof/door then stops the window holding the seal at full length.
Any help or tips?
Also any glue to be used for the foam on the soft top next to the window? I assume wind strip? it appears to have come away a little and traps between the door and weather strip at the back corner. I don't want to just cut this off if it's supposed to be in place.
Thanks.
part number 72381S2A013 WEATHERSTRIP, R. ROOF SIDE DOOR (or Lings image part number PFKL785135)
The roof was jetwashed by a young idiot at the bodyshop, and now that seal drips in the middle joint. The seal seems to have been fitted to the frame by some white glue/tape/boding putty, which is no longer sticky.
I assume this glue helps the weather strip stay stretched, it appears to be about 2mm too short for a proper seal. I can open the window and stretch the seal that little bit, then close the window, and everythings fine, But opening the window/roof/door then stops the window holding the seal at full length.
Any help or tips?
Also any glue to be used for the foam on the soft top next to the window? I assume wind strip? it appears to have come away a little and traps between the door and weather strip at the back corner. I don't want to just cut this off if it's supposed to be in place.
Thanks.
Si
#2743
Hello,
are you able to get the o-rings separately for the two sensors that bolt onto the rocker cover, one is a cam position sensor, cannot think what the other one is.
price and availability please
thanks
are you able to get the o-rings separately for the two sensors that bolt onto the rocker cover, one is a cam position sensor, cannot think what the other one is.
price and availability please
thanks
#2744
UK Trader
Thread Starter
#2745
Originally Posted by classicvin' timestamp='1427914015' post='23563004
Hello,
are you able to get the o-rings separately for the two sensors that bolt onto the rocker cover, one is a cam position sensor, cannot think what the other one is.
price and availability please
thanks
are you able to get the o-rings separately for the two sensors that bolt onto the rocker cover, one is a cam position sensor, cannot think what the other one is.
price and availability please
thanks
#2747
UK Trader
Thread Starter
Hi!
Sorry for the delay
Both O-Rings are the same for the TDC sensors - there are two.
http://www.hendyeshop.co.uk/o-ring-h...03-63990-p.asp
Sorry for the delay
Both O-Rings are the same for the TDC sensors - there are two.
http://www.hendyeshop.co.uk/o-ring-h...03-63990-p.asp
#2748
UK Trader
Thread Starter
76806SM5G03 is the correct Honda Part number - for a Washer Pump.
I can take 10% the RRP and free shipping. Will be circa £100
If you want to order I will get it set up on the site.
Si
#2749
Thanks Si I'm assuming this is the correct pump for the headlights washers?
I need to confirm its the pump that has failed but its looking likely. Will let you know after the weekend.
Thanks.
I need to confirm its the pump that has failed but its looking likely. Will let you know after the weekend.
Thanks.
#2750
UK Trader
Thread Starter
Yes - thats the one that came up when I transposed it with Lings it came up as that