What is With My Clutch?
#11
Administrator
In at least one severe case, the problem was 99% cleared up by greasing the input shaft and collar that the throwout bearing rides on.
The transmissions/clutch had been previously worked on by a Honda dealer and they left the thing bone dry. Once we greased it up and replaced the collar, all was well again. Of course this requires removing the transmission and is a major pita.
The transmissions/clutch had been previously worked on by a Honda dealer and they left the thing bone dry. Once we greased it up and replaced the collar, all was well again. Of course this requires removing the transmission and is a major pita.
#13
Originally posted by Asura
Can't you access the the shaft with the transmission in once you have the slave cylinder out?
Can't you access the the shaft with the transmission in once you have the slave cylinder out?
#14
Registered User
Join Date: Dec 2003
Location: Linden, VA (West by God)
Posts: 781
Likes: 0
Received 0 Likes
on
0 Posts
I STRONGLY suggest just lubing the clutch release fork before you go through getting the tranny dropped in order to deal with the TO bearing, etc.
To lube the clutch fork, all you need to do is:
- remove the slave cylinder
- pop the dust cover off the side of the bell housing
- give a pull on the release fork. Don't worry, you can't pull it all the way out.
- use some high temp grease on all the surfaces that come in contact with anything. That includes the pivot point and the ends of the two forks. This will be very obvious once you get under there. A screwdriver helps in applying the grease
This made a MONUMENTAL difference in my clutch actuation, and I strongly suggest doing it. Only takes 30 minutes.
To lube the clutch fork, all you need to do is:
- remove the slave cylinder
- pop the dust cover off the side of the bell housing
- give a pull on the release fork. Don't worry, you can't pull it all the way out.
- use some high temp grease on all the surfaces that come in contact with anything. That includes the pivot point and the ends of the two forks. This will be very obvious once you get under there. A screwdriver helps in applying the grease
This made a MONUMENTAL difference in my clutch actuation, and I strongly suggest doing it. Only takes 30 minutes.
#15
Registered User
Join Date: Mar 2004
Location: North Texas
Posts: 2,459
Likes: 0
Received 0 Likes
on
0 Posts
[QUOTE]
I STRONGLY suggest just lubing the clutch release fork before you go through getting the tranny dropped in order to deal with the TO bearing, etc.
To lube the clutch fork, all you need to do is:
- remove the slave cylinder
- pop the dust cover off the side of the bell housing
- give a pull on the release fork. Don't worry, you can't pull it all the way out.
- use some high temp grease on all the surfaces that come in contact with anything. That includes the pivot point and the ends of the two forks. This will be very obvious once you get under there. A screwdriver helps in applying the grease
This made a MONUMENTAL difference in my clutch actuation, and I strongly suggest doing it. Only takes 30 minutes.
I STRONGLY suggest just lubing the clutch release fork before you go through getting the tranny dropped in order to deal with the TO bearing, etc.
To lube the clutch fork, all you need to do is:
- remove the slave cylinder
- pop the dust cover off the side of the bell housing
- give a pull on the release fork. Don't worry, you can't pull it all the way out.
- use some high temp grease on all the surfaces that come in contact with anything. That includes the pivot point and the ends of the two forks. This will be very obvious once you get under there. A screwdriver helps in applying the grease
This made a MONUMENTAL difference in my clutch actuation, and I strongly suggest doing it. Only takes 30 minutes.
#17
Administrator
Originally posted by heffergm
I STRONGLY suggest just lubing the clutch release fork before you go through getting the tranny dropped in order to deal with the TO bearing, etc.
To lube the clutch fork, all you need to do is:
- remove the slave cylinder
- pop the dust cover off the side of the bell housing
- give a pull on the release fork. Don't worry, you can't pull it all the way out.
- use some high temp grease on all the surfaces that come in contact with anything. That includes the pivot point and the ends of the two forks. This will be very obvious once you get under there. A screwdriver helps in applying the grease
This made a MONUMENTAL difference in my clutch actuation, and I strongly suggest doing it. Only takes 30 minutes.
I STRONGLY suggest just lubing the clutch release fork before you go through getting the tranny dropped in order to deal with the TO bearing, etc.
To lube the clutch fork, all you need to do is:
- remove the slave cylinder
- pop the dust cover off the side of the bell housing
- give a pull on the release fork. Don't worry, you can't pull it all the way out.
- use some high temp grease on all the surfaces that come in contact with anything. That includes the pivot point and the ends of the two forks. This will be very obvious once you get under there. A screwdriver helps in applying the grease
This made a MONUMENTAL difference in my clutch actuation, and I strongly suggest doing it. Only takes 30 minutes.
Thread
Thread Starter
Forum
Replies
Last Post