DIY clutch replacement - thread for all my questions/problems
#11
Registered User
Thread Starter
Another question... If I'm resorting to cutting these off, could I use a reciprocating saw? I have one of those with some metal blades but no angle grinder.
The following users liked this post:
windhund116 (04-09-2023)
#12
The gear wrench xp120 slim long handle 1/4" ratchet, and a MATCO stubby 6 mm 1/4" hex socket will easily remove the prop shaft bolts with no stripping or headaches. Guaranteed, this has become one of my favorite wrenches, and if you get it you'll understand. It's like it was made to remove AP1 propshaft bolts.
https://www.amazon.com/GEARWRENCH-81034-Rat-120Xp-Hndl/dp/B078Z2V4CJ
https://www.matcotools.com/catalog/product/AXYS6M?srsltid=AfAwrE74dJ1y0D44eIu1lP4ldq-9eaFGxxbfmjfKJ4HmdtEyF8wPtmfn1yc
This wrench should be mandatory for anyone that works on these cars, it's that good.
The slim wrench head fits perfectly between the CV joint and center section. The MATCO socket fits like a glove and bottoms out on the bolt flush.
https://www.amazon.com/GEARWRENCH-81034-Rat-120Xp-Hndl/dp/B078Z2V4CJ
https://www.matcotools.com/catalog/product/AXYS6M?srsltid=AfAwrE74dJ1y0D44eIu1lP4ldq-9eaFGxxbfmjfKJ4HmdtEyF8wPtmfn1yc
This wrench should be mandatory for anyone that works on these cars, it's that good.
The slim wrench head fits perfectly between the CV joint and center section. The MATCO socket fits like a glove and bottoms out on the bolt flush.
Last edited by Slowcrash_101; 04-09-2023 at 11:17 AM.
The following users liked this post:
windhund116 (04-09-2023)
The following users liked this post:
windhund116 (04-09-2023)
#14
Registered User
Thread Starter
OK, please bear with me, as I am panicking slightly that I have started something I should not have...
I actually thought I had all the tools I would need for this job, but as it turns out, my hex socket is a tad too long as mentioned. My online options as a Canuck are somewhat limited, but Amazon.ca can get this to me by Tuesday --
I would feel better about this if someone could please say "yup, that should do the trick" or "no wtf, not THAT". It's 3/8 drive, not 3/4... otherwise it looks like it should do the trick. Plus my impact wrench is 3/8. <shrug>
The other issue is that one of them is already stripped... bloody hell. But I do have replacement OEM bolts, so whatever I have to do to take it out is fine.
I actually thought I had all the tools I would need for this job, but as it turns out, my hex socket is a tad too long as mentioned. My online options as a Canuck are somewhat limited, but Amazon.ca can get this to me by Tuesday --
I would feel better about this if someone could please say "yup, that should do the trick" or "no wtf, not THAT". It's 3/8 drive, not 3/4... otherwise it looks like it should do the trick. Plus my impact wrench is 3/8. <shrug>
The other issue is that one of them is already stripped... bloody hell. But I do have replacement OEM bolts, so whatever I have to do to take it out is fine.
#15
I strongly suggest you get that Matco hex socket, and the gearwrench 1/4" wrench. It fits perfectly and will make your life much easier. I had to give up my car for 3 weeks while waiting for my tailshaft housing to arrive. Being without a car is temporary, a job well done lasts much longer.
This is the closest thing, but without the slim head ratchet, you may not be able to get the hex socket flush with the bolt. The wrench is 9" long and let's you put more than enough leverage to remove the bolts. I routinely put my entire bodyweight on the wrench and it's still as good as new.
This is the closest thing, but without the slim head ratchet, you may not be able to get the hex socket flush with the bolt. The wrench is 9" long and let's you put more than enough leverage to remove the bolts. I routinely put my entire bodyweight on the wrench and it's still as good as new.
Last edited by Slowcrash_101; 04-09-2023 at 12:21 PM.
The following users liked this post:
windhund116 (04-09-2023)
#16
Registered User
Thread Starter
I strongly suggest you get that Matco hex socket, and the gearwrench 1/4" wrench. It fits perfectly and will make your life much easier. I had to give up my car for 3 weeks while waiting for my tailshaft housing to arrive. Being without a car is temporary, a job well done lasts much longer.
Titan 16141 Stubby Hex Bit Socket Set-9 Piece : Amazon.ca: Tools & Home Improvement
This is the closest thing, but without the slim head ratchet, you may not be able to get the hex socket flush with the bolt. The wrench is 9" long and let's you put more than enough leverage to remove the bolts. I routinely put my entire bodyweight on the wrench and it's still as good as new.
Titan 16141 Stubby Hex Bit Socket Set-9 Piece : Amazon.ca: Tools & Home Improvement
This is the closest thing, but without the slim head ratchet, you may not be able to get the hex socket flush with the bolt. The wrench is 9" long and let's you put more than enough leverage to remove the bolts. I routinely put my entire bodyweight on the wrench and it's still as good as new.
I suppose you don't endorse the practice of a wobble adapter in this particular case... which I think would preclude the need for a slim head ratchet, if I am properly visualizing the setup.
The following users liked this post:
windhund116 (04-09-2023)
#17
I tried that, it didn't work for me. The aforementioned tools were the most sure fire way I've found to date. I'm kind of clumsy and not exactly the best mechanic ever, so take what I say with a grain of salt.
#18
OK, please bear with me, as I am panicking slightly that I have started something I should not have...
I actually thought I had all the tools I would need for this job, but as it turns out, my hex socket is a tad too long as mentioned. My online options as a Canuck are somewhat limited, but Amazon.ca can get this to me by Tuesday -- https://www.amazon.ca/EMENTOL-Profil...8&sr=8-44&th=1
I would feel better about this if someone could please say "yup, that should do the trick" or "no wtf, not THAT". It's 3/8 drive, not 3/4... otherwise it looks like it should do the trick. Plus my impact wrench is 3/8. <shrug>
The other issue is that one of them is already stripped... bloody hell. But I do have replacement OEM bolts, so whatever I have to do to take it out is fine.
I actually thought I had all the tools I would need for this job, but as it turns out, my hex socket is a tad too long as mentioned. My online options as a Canuck are somewhat limited, but Amazon.ca can get this to me by Tuesday -- https://www.amazon.ca/EMENTOL-Profil...8&sr=8-44&th=1
I would feel better about this if someone could please say "yup, that should do the trick" or "no wtf, not THAT". It's 3/8 drive, not 3/4... otherwise it looks like it should do the trick. Plus my impact wrench is 3/8. <shrug>
The other issue is that one of them is already stripped... bloody hell. But I do have replacement OEM bolts, so whatever I have to do to take it out is fine.
The following users liked this post:
Slowcrash_101 (04-09-2023)
#19
Registered User
Thread Starter
I really appreciate the help, guys. Some tools are on order, so I'll give it another shot later in the week.
In the meantime I put in new transmission mounts so that I felt like I accomplished something.
In the meantime I put in new transmission mounts so that I felt like I accomplished something.
The following users liked this post:
Slowcrash_101 (04-10-2023)
#20
Registered User
You either need something that can fit into the space and allow you to manually apply enough torque, or you need something that can fit in the space and provide the torque from a distance - impact wrench/driver. An impact driver with a 6mm bit and a long bit holder come to mind if the slim ratchet is not an option for some reason. It may be easier to borrow an impact driver rather than an impact wrench as not many people own one compared to the other (at least in the UK).
If the stripped bolt is beyond saving, then yes, you will need to grind it out. I would try to make sure you have something that can sit on an undamaged bolt snugly and undo it before trying to work on the damaged bolt any further. You can go from maybe I don't need to grind it out to I absolutely have to grind it out rather swiftly using the wrong tool.
If the stripped bolt is beyond saving, then yes, you will need to grind it out. I would try to make sure you have something that can sit on an undamaged bolt snugly and undo it before trying to work on the damaged bolt any further. You can go from maybe I don't need to grind it out to I absolutely have to grind it out rather swiftly using the wrong tool.