S2000 Under The Hood S2000 Technical and Mechanical discussions.

Clutch Issues

Thread Tools
 
Old 11-25-2007, 11:52 AM
  #1  
Registered User
Thread Starter
 
IntenseImports's Avatar
 
Join Date: Oct 2003
Location: Clearwater
Posts: 277
Likes: 0
Received 0 Likes on 0 Posts
Default Clutch Issues

Hello All,
About a couple of months ago I had a clutch, pp and Lightened flywheel installed. I have been having some problems with the install part of things. THe car was running really funny before it used to refuse to go into any gear while at a dead stop, so we bled the clutch and adjusted the pedal to have zero freeplay and that seemed to fix the problem. Now about a month later the same problems are starting to arise again but not as bad. Sometimes its hard to put into gear when at a dead stop but this problem is not consistent. If initially I try to put it into gear and its difficult the attempts after that as long as the clutch is in it goes back to normal. Also when in high gears like 4th or 5th it kinda feels like the shifter is getting 'stuck' in the gear and is kind of hard to pull out of gear. We have also lubricated the input shaft and that seemed to improve the problem a little bit. Any input is appreciated.
Old 11-25-2007, 01:16 PM
  #2  
Registered User
 
DC2AP1's Avatar
 
Join Date: Jun 2007
Location: Laurentides,Quebec
Posts: 86
Likes: 0
Received 0 Likes on 0 Posts
Default

"Also when in high gears like 4th or 5th it kinda feels like the shifter is getting 'stuck' in the gear and is kind of hard to pull out of gear"

I have that problem too
Old 11-26-2007, 04:36 PM
  #3  
Registered User
Thread Starter
 
IntenseImports's Avatar
 
Join Date: Oct 2003
Location: Clearwater
Posts: 277
Likes: 0
Received 0 Likes on 0 Posts
Default

Old 11-27-2007, 07:33 PM
  #4  
Registered User
Thread Starter
 
IntenseImports's Avatar
 
Join Date: Oct 2003
Location: Clearwater
Posts: 277
Likes: 0
Received 0 Likes on 0 Posts
Default

ttt
Old 11-28-2007, 05:40 AM
  #5  
Registered User
 
nearwater4me's Avatar
 
Join Date: May 2006
Posts: 2,848
Likes: 0
Received 0 Likes on 0 Posts
Default

What kind of clutch kit was it? ACT?

Dan
Old 11-28-2007, 08:29 AM
  #6  
Registered User
Thread Starter
 
IntenseImports's Avatar
 
Join Date: Oct 2003
Location: Clearwater
Posts: 277
Likes: 0
Received 0 Likes on 0 Posts
Default

Its a OEM clutch kit with a ACT flywheel.

Thanks.
Old 11-29-2007, 06:04 PM
  #7  
Registered User
Thread Starter
 
IntenseImports's Avatar
 
Join Date: Oct 2003
Location: Clearwater
Posts: 277
Likes: 0
Received 0 Likes on 0 Posts
Default

No one?
Old 12-01-2007, 02:03 PM
  #8  
Registered User
Thread Starter
 
IntenseImports's Avatar
 
Join Date: Oct 2003
Location: Clearwater
Posts: 277
Likes: 0
Received 0 Likes on 0 Posts
Default

still need help
Old 12-02-2007, 05:47 AM
  #9  
H20
Registered User
 
H20's Avatar
 
Join Date: Oct 2007
Location: Milford
Posts: 86
Likes: 0
Received 0 Likes on 0 Posts
Default

I have been seeing these clutch issues on the boards off and on. I used to have a BMW2002 many years ago with this problem. I used to pump the clutch and it worked fine. I would say that if you bled it once and it worked then there must be air getting into the system. Have you tried pumping it at a stop and seeing if it helps. That would certainly point to air entering the system from somewhere.
Oh, the BMW turned upside down before I got to fixing the clutch.
Old 12-02-2007, 07:38 AM
  #10  
Registered User
 
captain_pants's Avatar
 
Join Date: Jun 2007
Location: Winnipeg, MB, Canada
Posts: 626
Likes: 0
Received 0 Likes on 0 Posts
Default

If you're sitting at rest with the car in 1st and the clutch depressed, does the car try to creep forwards? It sounds like the clutch might not be fully releasing. That could be a mechanical problem or a hydraulic problem. We need more info.

Did a local shop lighten the flywheel? They could have gotten the step dimensions wrong, that would cause the clutch disk to drag on the flywheel. Is the tranny full of oil? Have you tried bleeding the clutch hydraulics?


Quick Reply: Clutch Issues



All times are GMT -8. The time now is 10:35 AM.