AEM 1052 + NGK NTK AFX Wideband
#1
Registered User
Thread Starter
AEM 1052 + NGK NTK AFX Wideband
Hey all!
I've done a ton of searching on this issue and haven't found a concrete answer. Before I start guessing, where is the proper place to splice in/ pin my NGK wideband into my AEM 1052? It has the single output wire from the wideband unit itself.
I'm looking at this diagram, and see a few spots where it could make sense to put it...
http://static.summitracing.com/globa...vm-30-1052.pdf
Also, if anyone had the calibration information for it that would be awesome as well
I need to start data logging asap and this is the only thing stopping me!
Thank you so much for your time!
I've done a ton of searching on this issue and haven't found a concrete answer. Before I start guessing, where is the proper place to splice in/ pin my NGK wideband into my AEM 1052? It has the single output wire from the wideband unit itself.
I'm looking at this diagram, and see a few spots where it could make sense to put it...
http://static.summitracing.com/globa...vm-30-1052.pdf
Also, if anyone had the calibration information for it that would be awesome as well
I need to start data logging asap and this is the only thing stopping me!
Thank you so much for your time!
#2
Registered User
Join Date: Feb 2005
Location: Dallas, Tx
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
Hey all!
I've done a ton of searching on this issue and haven't found a concrete answer. Before I start guessing, where is the proper place to splice in/ pin my NGK wideband into my AEM 1052? It has the single output wire from the wideband unit itself.
I'm looking at this diagram, and see a few spots where it could make sense to put it...
http://static.summitracing.com/globa...vm-30-1052.pdf
Also, if anyone had the calibration information for it that would be awesome as well
I need to start data logging asap and this is the only thing stopping me!
Thank you so much for your time!
I've done a ton of searching on this issue and haven't found a concrete answer. Before I start guessing, where is the proper place to splice in/ pin my NGK wideband into my AEM 1052? It has the single output wire from the wideband unit itself.
I'm looking at this diagram, and see a few spots where it could make sense to put it...
http://static.summitracing.com/globa...vm-30-1052.pdf
Also, if anyone had the calibration information for it that would be awesome as well
I need to start data logging asap and this is the only thing stopping me!
Thank you so much for your time!
#3
Registered User
Thread Starter
Originally Posted by Dollabill' timestamp='1404682383' post='23232133
Hey all!
I've done a ton of searching on this issue and haven't found a concrete answer. Before I start guessing, where is the proper place to splice in/ pin my NGK wideband into my AEM 1052? It has the single output wire from the wideband unit itself.
I'm looking at this diagram, and see a few spots where it could make sense to put it...
http://static.summitracing.com/globa...vm-30-1052.pdf
Also, if anyone had the calibration information for it that would be awesome as well
I need to start data logging asap and this is the only thing stopping me!
Thank you so much for your time!
I've done a ton of searching on this issue and haven't found a concrete answer. Before I start guessing, where is the proper place to splice in/ pin my NGK wideband into my AEM 1052? It has the single output wire from the wideband unit itself.
I'm looking at this diagram, and see a few spots where it could make sense to put it...
http://static.summitracing.com/globa...vm-30-1052.pdf
Also, if anyone had the calibration information for it that would be awesome as well
I need to start data logging asap and this is the only thing stopping me!
Thank you so much for your time!
And yup I have the Powerdex with the ntk sensor. So far it's been great!
Thanks for your time!
Thread
Thread Starter
Forum
Replies
Last Post
RAIN H8R
S2000 Forced Induction
2
03-15-2015 07:01 PM