Leather Shift Boot Installation. . . Help!!
#1
Registered User
Thread Starter
Join Date: Oct 2000
Location: Bergen County
Posts: 862
Likes: 0
Received 0 Likes
on
0 Posts
I attempted to install Rick's leather shift boot last night and ran in to problems. . . Though the instructions were perfect, I couldn't remove the 2 side plastic clips or the 2 front clips. . . I used a screwdriver to push them in and tried pulling on the boot at the same time. . . They didn't move.
My biggest fear is breaking the clips off (should I be worrying about this?). Incidentally, the 2 bottom clips popped right out. . .
On a related topic. . . I could pull the radio cover off either (fear of breaking it). However, I probably won't install the Rick's console cover anytime soon. . . Kinda like the carpet. . .
My biggest fear is breaking the clips off (should I be worrying about this?). Incidentally, the 2 bottom clips popped right out. . .
On a related topic. . . I could pull the radio cover off either (fear of breaking it). However, I probably won't install the Rick's console cover anytime soon. . . Kinda like the carpet. . .
#2
Registered User
Join Date: Oct 2000
Location: The wilds of
Posts: 616
Likes: 0
Received 0 Likes
on
0 Posts
I just did this last weekend.
Make sure you've completely chipped off those two plastic plugs described in the instructions. Beyond that, I'd suggest wrapping your screwdriver with tape and working the clips gently. Use a strong light so you can see how they're moving and how far they have to go to get free.
This is the worst part of the installation, so just take it easy. Take it inside, get a cup of coffee and a light, and spend whatever time it takes. After that, it's a breeze.
Good luck, and let us know how it goes.
Make sure you've completely chipped off those two plastic plugs described in the instructions. Beyond that, I'd suggest wrapping your screwdriver with tape and working the clips gently. Use a strong light so you can see how they're moving and how far they have to go to get free.
This is the worst part of the installation, so just take it easy. Take it inside, get a cup of coffee and a light, and spend whatever time it takes. After that, it's a breeze.
Good luck, and let us know how it goes.
#4
Registered User
Join Date: Oct 2000
Location: Deptford, New Jersey
Posts: 3,698
Received 0 Likes
on
0 Posts
check out the thread in "meets and events" section for "Meet Rick Hesel Day" if you still dont want to mess with it you can get some help at the meet.
#5
Former Sponsor
Those six clips that hold on the boot frame are the toughest part of the shift boot installation. The two nearest the armrest are the easiest -- you can leverage them out with a flathead screwdriver. The two on the sides and at the front are much tougher. I make it easier by taking a sharp utility or Exacto knife and trimming off about 1/32 along the edge of each clip. That's just enough to make them easier to release.
Release the two in the back first, and keep them released as you work (they'll want to pop back in). Release the side clips next and the two in the front last.
Release the two in the back first, and keep them released as you work (they'll want to pop back in). Release the side clips next and the two in the front last.
#7
Iceman,
Trying to avoid breaking the clips was definitely the toughest part of the shift boot installation for me. It probably took me an hour to do the shift boot installation because I was being so careful.
The console cover, on the other hand, was very easy. Just give a good yank on the radio cover & the clips will release.
In my opinion, the console cover is the biggest asthetic improvement to the car! Thanks, Rick!!
Trying to avoid breaking the clips was definitely the toughest part of the shift boot installation for me. It probably took me an hour to do the shift boot installation because I was being so careful.
The console cover, on the other hand, was very easy. Just give a good yank on the radio cover & the clips will release.
In my opinion, the console cover is the biggest asthetic improvement to the car! Thanks, Rick!!
Trending Topics
#10
Registered User
Join Date: Oct 2000
Location: Del Boca Vista
Posts: 1,148
Likes: 0
Received 0 Likes
on
0 Posts
Once you get the console piece separated to allow you to remove the old boot and replace it with the new one, be super, extra careful with the little plastic "teats" which run around the edge of the boot mount. I was very careful and still broke two of them off... no big deal if a few go, but the fewer the better...
Hey Rick, did you get anywhere in your consideration of wood or plastic side panels for the console cover? I haven't put mine in yet, and I am concerned about the sides coming undone, having wrinkles, or just looking tacked on.
Hey Rick, did you get anywhere in your consideration of wood or plastic side panels for the console cover? I haven't put mine in yet, and I am concerned about the sides coming undone, having wrinkles, or just looking tacked on.