From 375whp Turbo S2k.. Boom...to: built LS6 with a bunch of goodies !
#181
Registered User
Thread Starter
Join Date: Jul 2012
Posts: 1,146
Likes: 0
Received 0 Likes
on
0 Posts
Currently sitting at McCarren airport in Vegas waiting for my flight home, allll my parts should be in within a week or 2, engine bay will be completed this week hopefully!! I also ordered a clutch bracket !! Slick piece !!!!
#182
Registered User
Thread Starter
Join Date: Jul 2012
Posts: 1,146
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Reapur' timestamp='1359190330' post='22294213
Yeah, never seen a V8 with a single exit. This exhaust setup will be a restriction in power for sure. Weight savings would be minimal in comparison with power loss.
Thanks for all the comments People ! Much appreciated
More updates in a couple days I'm sure just been out of town !
Lee
#183
Registered User
Thread Starter
Join Date: Jul 2012
Posts: 1,146
Likes: 0
Received 0 Likes
on
0 Posts
Hey Lee, I should have my rear diff mounted shortly just waiting on some parts to come back in. depending on what axles you want to use (i am using the ford axles with rebroached hubs) which to be honest i dont recomend and wont do again as DSS did not broach them right and they were extreamly tight and took a couple hours each to get the axles to fit without binding completely half way through. Ill probably make some custom shafts later on and install stock hubs again with s2000 outers and custome axle shafts. I should hopefully have some pics of it mounted in a week or so on v8s2000.com build is coming along nicely
Thanks for the update !! Dss is great but they are currently in the middle of a move so it took almost a month for my driveshaft !
Lee
#184
#186
Registered User
Thread Starter
Join Date: Jul 2012
Posts: 1,146
Likes: 0
Received 0 Likes
on
0 Posts
I will be stock for a while ...... looking into Puddy mod stage 2 3.73 set up .... with dss upgraded stock style axles ...
easiest without relocating anything or changing hubs bearings abs function and my new driveshaft...and I can do it in stages, get the diff first then save for axles !
how about you ??
-Lee
easiest without relocating anything or changing hubs bearings abs function and my new driveshaft...and I can do it in stages, get the diff first then save for axles !
how about you ??
-Lee
#188
Registered User
Thread Starter
Join Date: Jul 2012
Posts: 1,146
Likes: 0
Received 0 Likes
on
0 Posts
#189
Registered User
Thread Starter
Join Date: Jul 2012
Posts: 1,146
Likes: 0
Received 0 Likes
on
0 Posts
and BTW, flywheel is back from machine shop, clutch showed up !!! so I can get that all measured up and installed this weekend hopefully, rad is back from being modified one last time (hopefully) and I have 2 more packages at the post office !!! its like chrismas everytime I go there haha !! lots of pics to come this weekend !!! woot !!!
-Lee
-Lee
#190
Registered User
Thread Starter
Join Date: Jul 2012
Posts: 1,146
Likes: 0
Received 0 Likes
on
0 Posts
I couldnt wait haha I installed the clutch measured it up and took some pics of the parts I received !
more to come for sure !
pics !!
custom driveshaft from DSS, nice piece and weighs NOTHING !!! just over 2ft long hshaha
special plate that is required to go from dss shaft to ap1 rear end
flywheel back from the machine shop !!
mounted
friction disc
PP installed and torqued
finally the upgraded GM performance slave, with remote bleeder and all stainless lines !!!
more to come for sure !
pics !!
custom driveshaft from DSS, nice piece and weighs NOTHING !!! just over 2ft long hshaha
special plate that is required to go from dss shaft to ap1 rear end
flywheel back from the machine shop !!
mounted
friction disc
PP installed and torqued
finally the upgraded GM performance slave, with remote bleeder and all stainless lines !!!