Flashpro w/ aem wideband question?
#22
Registered User
Join Date: Jul 2006
Location: Calgary, Alberta
Posts: 877
Likes: 0
Received 0 Likes
on
0 Posts
Did you get this sorted out?
If I run it to ECT2. Do I have to uncheck any boxes like ELD?
I actually tried to add a pin for B12, but it's not showing any voltage in my logs..... Maybe the pin didn't go in properly.
I figure I may as well try ELD or ECT2 as they were pinned from the factory and I just have to cut and soldier.
If I run it to ECT2. Do I have to uncheck any boxes like ELD?
I actually tried to add a pin for B12, but it's not showing any voltage in my logs..... Maybe the pin didn't go in properly.
I figure I may as well try ELD or ECT2 as they were pinned from the factory and I just have to cut and soldier.
#23
Sorry for being so ignorant here. I have a 2006 with Hondata FlashPro. When I installed my wideband failsafe gauge I did it as a stand alone unit, welded in a bung. Am I somehow missing out by not having the ECU look at the AEM gauge? I did not know it was even possible! And what does the Electrical Load Detector have to do with the AEM gauge. Again sorry for my ignorance here.
I can tell where the tach signal wire is(2006 and higher):
Your ECM should have 1 gray connector and 3 white ones. Find the largest of the white connectors and you will see it has 3 long rows of terminals. Look for a blue wire near the middle of the row that is opposite from the connector latch, which means it's on the "back side" so you'll probably have to pull the connector off the ECU to get to it. You'll see the back row of terminals has t terminal slots by themselves, one of which is empty. The other hole should have the blue tach wire. There are only 2 blue wires in this connector and the other one is on a "front side corner" of the connector so it should not be hard to find the tach signal wire.
I can tell where the tach signal wire is(2006 and higher):
Your ECM should have 1 gray connector and 3 white ones. Find the largest of the white connectors and you will see it has 3 long rows of terminals. Look for a blue wire near the middle of the row that is opposite from the connector latch, which means it's on the "back side" so you'll probably have to pull the connector off the ECU to get to it. You'll see the back row of terminals has t terminal slots by themselves, one of which is empty. The other hole should have the blue tach wire. There are only 2 blue wires in this connector and the other one is on a "front side corner" of the connector so it should not be hard to find the tach signal wire.
#24
Sorry for being so ignorant here. I have a 2006 with Hondata FlashPro. When I installed my wideband failsafe gauge I did it as a stand alone unit, welded in a bung. Am I somehow missing out by not having the ECU look at the AEM gauge? I did not know it was even possible! And what does the Electrical Load Detector have to do with the AEM gauge. Again sorry for my ignorance here.
I can tell where the tach signal wire is(2006 and higher):
Your ECM should have 1 gray connector and 3 white ones. Find the largest of the white connectors and you will see it has 3 long rows of terminals. Look for a blue wire near the middle of the row that is opposite from the connector latch, which means it's on the "back side" so you'll probably have to pull the connector off the ECU to get to it. You'll see the back row of terminals has t terminal slots by themselves, one of which is empty. The other hole should have the blue tach wire. There are only 2 blue wires in this connector and the other one is on a "front side corner" of the connector so it should not be hard to find the tach signal wire.
I can tell where the tach signal wire is(2006 and higher):
Your ECM should have 1 gray connector and 3 white ones. Find the largest of the white connectors and you will see it has 3 long rows of terminals. Look for a blue wire near the middle of the row that is opposite from the connector latch, which means it's on the "back side" so you'll probably have to pull the connector off the ECU to get to it. You'll see the back row of terminals has t terminal slots by themselves, one of which is empty. The other hole should have the blue tach wire. There are only 2 blue wires in this connector and the other one is on a "front side corner" of the connector so it should not be hard to find the tach signal wire.
#25
Lots of misinformation in this thread. Below are the facts.
First of all, the stock primary o2 sensor for a 2005-2009 S2000 is a wideband.
Second of all if you want to run in closed loop you must use the stock primary o2 sensor.
Any aftermarket wideband used and wired to one of the other ECU inputs is just for datalogging purposes, and you cannot run closed loop from it.
First of all, the stock primary o2 sensor for a 2005-2009 S2000 is a wideband.
Second of all if you want to run in closed loop you must use the stock primary o2 sensor.
Any aftermarket wideband used and wired to one of the other ECU inputs is just for datalogging purposes, and you cannot run closed loop from it.
#26
Lots of misinformation in this thread. Below are the facts.
First of all, the stock primary o2 sensor for a 2005-2009 S2000 is a wideband.
Second of all if you want to run in closed loop you must use the stock primary o2 sensor.
Any aftermarket wideband used and wired to one of the other ECU inputs is just for datalogging purposes, and you cannot run closed loop from it.
First of all, the stock primary o2 sensor for a 2005-2009 S2000 is a wideband.
Second of all if you want to run in closed loop you must use the stock primary o2 sensor.
Any aftermarket wideband used and wired to one of the other ECU inputs is just for datalogging purposes, and you cannot run closed loop from it.
I ask you SLWS2K, what are doing in FlashPro with the AEM and the ELD. Sorry, I just cannot follow what you are trying to do.
#27
Connecting the aem sensor to the ecu allows the tuner and owner to view afr from the datalog.
" The OEM primary o2 sensor does not read accurately, and actually varies from car to car how well it reads against a actual wideband o2 sensor. The primary o2 sensor is fine for closed loop partial throttle control, but is not accurate enough for dial in proper a/f under boost. Further, the sensors are EGT driven so the hotter the exhaust gets the sensor will read worse and worse."
" The OEM primary o2 sensor does not read accurately, and actually varies from car to car how well it reads against a actual wideband o2 sensor. The primary o2 sensor is fine for closed loop partial throttle control, but is not accurate enough for dial in proper a/f under boost. Further, the sensors are EGT driven so the hotter the exhaust gets the sensor will read worse and worse."
#28
Connecting the aem sensor to the ecu allows the tuner and owner to view afr from the datalog.
" The OEM primary o2 sensor does not read accurately, and actually varies from car to car how well it reads against a actual wideband o2 sensor. The primary o2 sensor is fine for closed loop partial throttle control, but is not accurate enough for dial in proper a/f under boost. Further, the sensors are EGT driven so the hotter the exhaust gets the sensor will read worse and worse."
" The OEM primary o2 sensor does not read accurately, and actually varies from car to car how well it reads against a actual wideband o2 sensor. The primary o2 sensor is fine for closed loop partial throttle control, but is not accurate enough for dial in proper a/f under boost. Further, the sensors are EGT driven so the hotter the exhaust gets the sensor will read worse and worse."
In the next part you quote something(do not know what you are quoting)that says the factory O2 sensor is shit. But that is all it says. It infers that since it is shit you should use the AEM sensor instead.
So do you connect it for just reading the data logs for do you connect it for control?
#29
Originally Posted by crxdx' timestamp='1408990720' post='23301054
Connecting the aem sensor to the ecu allows the tuner and owner to view afr from the datalog.
" The OEM primary o2 sensor does not read accurately, and actually varies from car to car how well it reads against a actual wideband o2 sensor. The primary o2 sensor is fine for closed loop partial throttle control, but is not accurate enough for dial in proper a/f under boost. Further, the sensors are EGT driven so the hotter the exhaust gets the sensor will read worse and worse."
" The OEM primary o2 sensor does not read accurately, and actually varies from car to car how well it reads against a actual wideband o2 sensor. The primary o2 sensor is fine for closed loop partial throttle control, but is not accurate enough for dial in proper a/f under boost. Further, the sensors are EGT driven so the hotter the exhaust gets the sensor will read worse and worse."
In the next part you quote something(do not know what you are quoting)that says the factory O2 sensor is shit. But that is all it says. It infers that since it is shit you should use the AEM sensor instead.
So do you connect it for just reading the data logs for do you connect it for control?
I really don't understand why you're confused you're making it harder than it really is. You can run the wire to the ECU if you want more accurate data logs especially if your boosted. I was quoting Jeff Evans he is a very reputable tuner these are his opinions on the factory wideband. They are just not suitable for boost they become very inaccurate.
I run the factory o2 sensor and the AEM. The AEM wideband or any aftermarket sensor and gauge is used for reference and tuning only. You can hook it up to the ecu if you WANT to this makes tuning much easier and accurate instead of eyeballing the gauge.