S2KI Honda S2000 Forums

S2000 Brakes and Suspension Discussions about S2000 brake and suspension systems.
Sponsored by:
Sponsored by: Sake Bomb

Official Stoptech BBK Wheel Fitment Thread

Thread Tools
 
Old 03-05-2016, 03:20 PM
  #441  
Registered User

 
Shinobi77's Avatar
 
Join Date: Jun 2013
Posts: 18
Likes: 0
Received 3 Likes on 1 Post
Default
Ok, people confirmed that the Advan RZ 17x8 +45 will clear the stoptechs, but will the 9 inch, sames specs clear without spacers?? Just curious... Didn't see a confirmation on the 9 inch wide wheel.. Thanks guys!
Shinobi77 is offline  
Reply Like
Old 03-05-2016, 04:11 PM
  #442  

 
afzan's Avatar
 
Join Date: Mar 2010
Location: Toronto
Posts: 3,601
Received 103 Likes on 85 Posts
Default
^ yes they will, you could fit two calipers in there, lol
afzan is offline  
Reply Like
Old 04-18-2016, 05:35 PM
  #443  
Gold Member (Premium)
 
yamahaSHO's Avatar
 
Join Date: Sep 2012
Location: Greenwood, AR
Posts: 3,214
Received 142 Likes on 113 Posts
Default
Just put StopTech brakes on my car, what I found (and you may already know):

TSW Nurburgring 17x9 - FIT
TSW Interlagos 17x9 - 3mm spacer (may get away with 2mm).
yamahaSHO is offline  
Reply Like
Old 06-06-2016, 12:20 PM
  #444  
Community Organizer
Community Organizer
 
goldenfri's Avatar
 
Join Date: Nov 2005
Location: Maryland
Posts: 16,476
Received 708 Likes on 448 Posts
Default
Originally Posted by goldenfri
Originally Posted by goldenfri' timestamp='1420581474' post='23458568
Originally Posted by Back S2k' timestamp='1420567024' post='23458215
Skimmed the whole thread and didn't see anything on the buddy club p1 wheels, they seem like they would clear the 328kit 17x9 et45.
I have two sets of these wheels, one staggered (17x8 +45 in the front), one non-staggered (17x9 +63 in the front) and I just picked up the 328 stop tech kit. I think the +63s are going to need some significant spacers, 17x8 +45 is going to need something but not nearly as much, but I need to do more measuring before I buy spacers. I'll post in here when I find out for sure what is needed.
Ok, using the cutout template the 17x9 +63 will fit with a 10mm spacer but is pretty close. The 17x8 +45 will fit with a 5mm spacer but has a bit more room, so you might be able to get away with a 3 or 4mm spacer. I am going to buy some spacers and I'll report back after I actually test fit them in a month or two.

It has been a while, but I can confirm that the 17x9 +63 buddy club P1 QF forged wheels work with the 328 stoptech kit using a 10mm spacer.
Last edited by goldenfri; 03-12-2019 at 09:14 AM.
goldenfri is offline  
Reply Like
Old 07-23-2016, 06:58 PM
  #445  
Registered User
 
NFR-S2k-'s Avatar
 
Join Date: Nov 2015
Location: Tallahassee, FL
Posts: 529
Received 4 Likes on 4 Posts
Default
Anyone tried the 17x7.5 +45 tsw nurburgrings? I printed the template today and it seemed to have enough room between the spokes and the template but the template hit the top of the wheels and bent it quite a bit. I couldnt figure out what i was doing wrong lol. Btw, i followed stoptech's instructions and measured everything correctly but I was just curious if anyone has tried a stoptech bbk with the 7.5 tsw's.
NFR-S2k- is offline  
Reply Like
Old 07-29-2016, 01:18 AM
  #446  
Registered User

 
leon_83's Avatar
 
Join Date: Apr 2011
Posts: 24
Likes: 0
Received 0 Likes on 0 Posts
Default
Originally Posted by energetic
Although this is a new wheel in the market at 17" wheel size, has anyone fitted a Volk Racing ZE40 with Stoptech 328x28?

I am considering fitting them. The following size is being recommended by Rays Engineering:

Front 17 x 7.5 +48
Rear 17 x 9.0 +61

Any spacer required for the ZE40? They look in fact as BBK friendly compared to the CE28N which I have now as below:

Front 17 x 7.5 JJ / Off +50
Rear 17 x 9.0 JJ / Off +63

More details on my current setup is being described here, as well as in the first page of this thread.

+1. interested. I bought a set of ze40
leon_83 is offline  
Reply Like
Old 08-01-2016, 06:46 AM
  #447  
Registered User
 
MrCouch's Avatar
 
Join Date: Jan 2016
Posts: 173
Received 2 Likes on 2 Posts
Default
Has anyone tried to fit Stoptech kit under the Spoon cr93 wheels? 17x8.5+53 F 17x9.5+63 R?
MrCouch is offline  
Reply Like
Old 08-07-2016, 07:35 PM
  #448  
Registered User
 
dttrllc's Avatar
 
Join Date: May 2015
Posts: 14
Likes: 0
Received 0 Likes on 0 Posts
Default
Has anyone tried Advan RG 3 17x8 +54 ? I have these wheels and would like to upgrade to these 328mm for my track setup.
dttrllc is offline  
Reply Like
Old 08-08-2016, 05:58 PM
  #449  

 
roel03's Avatar
 
Join Date: Jan 2012
Location: Florida
Posts: 961
Received 250 Likes on 147 Posts
Default
Advan RSII 17x9+63 does not clear the ST40 template. With a 2-3mm spacer I think it would fit. The ID does not clear the ST60.
roel03 is offline  
Reply Like
Old 08-25-2016, 12:30 PM
  #450  

 
tkeyyy's Avatar
 
Join Date: Oct 2008
Location: Bay Area, California
Posts: 6,765
Likes: 0
Received 2 Likes on 2 Posts
Default
Originally Posted by copmagnet82
Originally Posted by UncleHo79' timestamp='1446717916' post='23795658
Here some pictures of my new Advan RZ 8x17 et45 with the st40 Stoptech. It clears the caliper about 2mm without spacers.

How did you get the caliper without the Stoptech logo? Did you repaint them or did you get them special ordered like that?
they installed them upside down. bleeder valves need to be at the top, not the bottom.

will be installing the ST40 in the next few days on my s with 17x9 +40 re30 clubsport. will post photos when it's done
tkeyyy is offline  
Reply Like



Advanced Search
Quick Reply: Official Stoptech BBK Wheel Fitment Thread


Reply Closed Thread Share

All times are GMT -8. The time now is 02:55 PM.