Mark this thread as Sold
TN - Motor Part out / Garage Sale! CP Pistons, BC Rods, F20 Crank, & More!
11-19-2015, 07:55 AM
#1
TN - Motor Part out / Garage Sale! CP Pistons, BC Rods, F20 Crank, & More!
First Name: Riley
Price: All listed
Location: Knoxville TN, 37902 ZIP
Contact: 865 591 0462, PM goes to email, but text is quicker.
------------------------------------------------------------------------------------------------------------------------------
First off, quick few things, anything can be shipped, prices are before shipping, unless stated. SKIP BELOW TO PART OUT PRICES.
------------------------------------------------------------------------------------------------------------------------------
Currently, the aftermarket internals are inside of an assembled F20C shortblock, which can be sold for $1,500 OBO. I was told 43k miles before initial disassembly. I have not confirmed. It has NEVER been run.
-----> this is priced extrmeley low due to the fact it was accidentally decked 0.024", while 0.008" is the service limit. Running a thicker HG can be used to correct this, your risk, I chose not to. Hence why I will also part it.
-WHEN the first person purchases a part of this motor, pistons, rods, etc, I will disassemble it and remove the part to ship.
------------------------------------------------------------------------------------------------------------------------------
-some accessories may be removed depending on if it sells whole, and where that price goes.
---> F20C WHOLE shortblock price of $1,500 includes;
- CP Pistons, 87mm bore, 10:1 comp. P/n. SC7065
- block - Darton dry / flanged sleeves - decked 0.0024" (timing cover matches) as stated above.
- BC sportsman rods - ARP2000 bolts. P/n. BC6064
- F20C good condtion crankshaft
- ACL race bearings - std size - main / rod / thrust
- ARP head studs are NOT included.
- timing set up, guides, chain
- crank pulley
- water pump
- oil pump
- mount brackets
- oil pan - not pictured - not bolted / sealed on.
- probably forgetting some small things
-------------------------------------------------------------------------------------------------------------------------------
PART OUT LIST & PRICES
- CP Pistons, 87mm bore, 10:1 comp. P/n. SC7065 ---- $450
- block - Darton dry / flanged sleeves - decked 0.0024" + matching timing cover --- $500
- BC sportsman rods - ARP2000 bolts. P/n. BC6064 --- $350
- F20C good condition crankshaft --- $350
- AP1 Valve cover - crappy paint, has oil cap and both sensor plugs - sold
- oil pan --- $100
- Intake manifold, w/ idle valve and sensor - $75 , no throttle body
- throttle body w/ map sensor and tps - sold
- fuel rail, no injectors - $20
- injector oem set - sold
- AP1 Coil packs - Can test with OBDII scanner - sold
- timing set up, guides, chain, no tct - $50
- OEM TCT - sold
- F22C AP2 piston / rod set - broken rings, pistons appear undamaged, no bearings spun, rods are good - sold
- F20C AP1 piston / rod set - one shredded piston skirt, other 3 look nearly perfect, no spun bearings, rods are good. - $75
- crank pulley - no rust - $50
- water pump - $30
- mount brackets - $30
Price: All listed
Location: Knoxville TN, 37902 ZIP
Contact: 865 591 0462, PM goes to email, but text is quicker.
------------------------------------------------------------------------------------------------------------------------------
First off, quick few things, anything can be shipped, prices are before shipping, unless stated. SKIP BELOW TO PART OUT PRICES.
------------------------------------------------------------------------------------------------------------------------------
Currently, the aftermarket internals are inside of an assembled F20C shortblock, which can be sold for $1,500 OBO. I was told 43k miles before initial disassembly. I have not confirmed. It has NEVER been run.
-----> this is priced extrmeley low due to the fact it was accidentally decked 0.024", while 0.008" is the service limit. Running a thicker HG can be used to correct this, your risk, I chose not to. Hence why I will also part it.
-WHEN the first person purchases a part of this motor, pistons, rods, etc, I will disassemble it and remove the part to ship.
------------------------------------------------------------------------------------------------------------------------------
-some accessories may be removed depending on if it sells whole, and where that price goes.
---> F20C WHOLE shortblock price of $1,500 includes;
- CP Pistons, 87mm bore, 10:1 comp. P/n. SC7065
- block - Darton dry / flanged sleeves - decked 0.0024" (timing cover matches) as stated above.
- BC sportsman rods - ARP2000 bolts. P/n. BC6064
- F20C good condtion crankshaft
- ACL race bearings - std size - main / rod / thrust
- ARP head studs are NOT included.
- timing set up, guides, chain
- crank pulley
- water pump
- oil pump
- mount brackets
- oil pan - not pictured - not bolted / sealed on.
- probably forgetting some small things
-------------------------------------------------------------------------------------------------------------------------------
PART OUT LIST & PRICES
- CP Pistons, 87mm bore, 10:1 comp. P/n. SC7065 ---- $450
- block - Darton dry / flanged sleeves - decked 0.0024" + matching timing cover --- $500
- BC sportsman rods - ARP2000 bolts. P/n. BC6064 --- $350
- F20C good condition crankshaft --- $350
- AP1 Valve cover - crappy paint, has oil cap and both sensor plugs - sold
- oil pan --- $100
- Intake manifold, w/ idle valve and sensor - $75 , no throttle body
- throttle body w/ map sensor and tps - sold
- fuel rail, no injectors - $20
- injector oem set - sold
- AP1 Coil packs - Can test with OBDII scanner - sold
- timing set up, guides, chain, no tct - $50
- OEM TCT - sold
- F22C AP2 piston / rod set - broken rings, pistons appear undamaged, no bearings spun, rods are good - sold
- F20C AP1 piston / rod set - one shredded piston skirt, other 3 look nearly perfect, no spun bearings, rods are good. - $75
- crank pulley - no rust - $50
- water pump - $30
- mount brackets - $30
Thread
Thread Starter
Forum
Replies
Last Post
Akilldema
Member S2000 Classifieds and For Sale
40
04-26-2007 01:54 PM