Mark this thread as Sold
Big Race Part out
09-10-2010 | 05:22 PM
#1
Thread Starter
Registered User
Joined: Sep 2009
Posts: 81
Likes: 0
Big Race Part out
Location: Louisville, Kentucky
The best way to contact me is through e-mail at Cnaylor161@gmail.com
Integra Part Out
I have decided to part out the integra, i am going a different route with a different chassis, so i begin to part out the build. Everything has less then 5 miles, the components have never seen any power, as i just ran the car and never got a tune on the car. I have a lot of people that can vouch for me and my parts. Rob Morse @ TPR Tony palo @ T1racedevelopment Fernando Reyes @ Kings Performance. Please message me for any offers, and only serious offers. Everything here is of high quality, so i wont accept any low balls.
You can also contact me through email cnaylor161@gmail.com
thanks a lot. I accept paypal, shipping and paypal fees will be applied.
T1 Ultimate Ignition Kit. Comes with M&W ignition box with harness, CBR coils, T1 cam trigger sensor, and golden eagle Exhaust cam gear. 1700 OBO
Full race traction bar 250
Competition Twin Disc for Bseries SOLD
TPR short block
Specs:
B18B1 Bottom end
ERL darton MID sleeves
CP pistons
CP Rings
Manley turbo tuff rods
Calico coating on pistons
align hone engine block
Cylinder hone
ERL 5 point main girdle
ARP main studs
4000OBO
Precision billet 6768 with .96 AR exhaust housing NON ball bearing
1300OBO
1 precision 46mm wastegates 290
Motec Milspec T1 M800 race spec harness - 2800 OBO SOLD
Motec M400 ECU - 3200 OBO SOLD
Koyo radiator with -16 welded bungs with top of radiator welded off with the lines and fittings 2 90 and 2 straight fittings.
600 OBO
T1 Catchcan divided into 3 parts coolant fill, overflow, and breather system. Comes with -4 line with fittings. all -10 lines for valve cover and back of block with the freeze plugs on block and -12 coolant line and fitting
800 OBO
T1 intercooler with 3 inch intercooler piping to fit dc2 integra and also will fit an EG, the intercooler piping routes through the engine bay, not through any chassis holes.
1000 OBO
AEM similar electronic boost controller - 70
Avid solid mounts for DC2 integra - 400
Oil filter sandwich plate for turbo feed line and Lsvtec line - 80
-4 turbo feed line with nylon sleeve over the line - 90
Moroso 5.5 quart oil pan with Moroso oil pickup 350
1995 Integra GSR shell. Has sunroof and power everything, car does not have seats other than a tan DC2 driver and passenger seat. sunroof. No rust, painted berlina black. Side moldings have been deleted. Fully shaved bay painted candy gold. comes with genuine 00 ITR head lights. if you have any questions please message me more.
1500
I may have left other things out, if you would like to see pictures i can email you those, again everything from this part out has VERY VERY low miles less than 5 miles it all.
The best way to contact me is through e-mail at Cnaylor161@gmail.com
Integra Part Out
I have decided to part out the integra, i am going a different route with a different chassis, so i begin to part out the build. Everything has less then 5 miles, the components have never seen any power, as i just ran the car and never got a tune on the car. I have a lot of people that can vouch for me and my parts. Rob Morse @ TPR Tony palo @ T1racedevelopment Fernando Reyes @ Kings Performance. Please message me for any offers, and only serious offers. Everything here is of high quality, so i wont accept any low balls.
You can also contact me through email cnaylor161@gmail.com
thanks a lot. I accept paypal, shipping and paypal fees will be applied.
T1 Ultimate Ignition Kit. Comes with M&W ignition box with harness, CBR coils, T1 cam trigger sensor, and golden eagle Exhaust cam gear. 1700 OBO
Full race traction bar 250
Competition Twin Disc for Bseries SOLD
TPR short block
Specs:
B18B1 Bottom end
ERL darton MID sleeves
CP pistons
CP Rings
Manley turbo tuff rods
Calico coating on pistons
align hone engine block
Cylinder hone
ERL 5 point main girdle
ARP main studs
4000OBO
Precision billet 6768 with .96 AR exhaust housing NON ball bearing
1300OBO
1 precision 46mm wastegates 290
Motec Milspec T1 M800 race spec harness - 2800 OBO SOLD
Motec M400 ECU - 3200 OBO SOLD
Koyo radiator with -16 welded bungs with top of radiator welded off with the lines and fittings 2 90 and 2 straight fittings.
600 OBO
T1 Catchcan divided into 3 parts coolant fill, overflow, and breather system. Comes with -4 line with fittings. all -10 lines for valve cover and back of block with the freeze plugs on block and -12 coolant line and fitting
800 OBO
T1 intercooler with 3 inch intercooler piping to fit dc2 integra and also will fit an EG, the intercooler piping routes through the engine bay, not through any chassis holes.
1000 OBO
AEM similar electronic boost controller - 70
Avid solid mounts for DC2 integra - 400
Oil filter sandwich plate for turbo feed line and Lsvtec line - 80
-4 turbo feed line with nylon sleeve over the line - 90
Moroso 5.5 quart oil pan with Moroso oil pickup 350
1995 Integra GSR shell. Has sunroof and power everything, car does not have seats other than a tan DC2 driver and passenger seat. sunroof. No rust, painted berlina black. Side moldings have been deleted. Fully shaved bay painted candy gold. comes with genuine 00 ITR head lights. if you have any questions please message me more.
1500
I may have left other things out, if you would like to see pictures i can email you those, again everything from this part out has VERY VERY low miles less than 5 miles it all.
Location?
